banner



How To Install Shock Absorber

Download Article

Download Article

If you need to replace your car's shock absorbers but don't want to pay an expensive mechanic's fee, you can do so on your own with a little effort. Shocks are essential to a car's performance, giving it a smooth and even ride. Over time, however, the vehicle's suspensions become worn out. You may notice potholes and speed bumps are more severe and uncomfortable to drive over. In this case, you'll want to replace your shocks, which you can do at home in an afternoon with the right materials and a little elbow grease!

  1. 1

    Make sure you need new shocks. You might have noticed going over potholes and bumps isn't as smooth as it used to be in your ride, which is probably a sign that your shocks are worn out and need replaced. A good easy way to test your shocks and make sure they're worn out enough to be replaced is to push down hard on the trunk or the hood directly above the wheel well. Good shocks should bounce up once and settle relatively quickly. If the body bounces any more than that after pushing, it's time for a new set.[1]

    • You also need to know if your vehicle uses stand-alone shocks that attach to the vehicle suspension or frame, or if it uses shock-absorber units which integrated into a suspension strut, such as the MacPherson or Chapman strut. Your car may even have a combination, using shocks in the front and struts in the back. Struts can be difficult to replace, so it's best to let a professional handle that job.[2]
  2. 2

    Purchase new shock absorbers. If you're unsure what type of shock absorbers you need, speak to someone at your local auto parts store or an auto mechanic to be sure you buy the right shock absorbers or piston for your vehicle.

  3. 3

    Consider upgrading your shocks. You can get identical replacements of the shocks you have in your car currently, but taking the time to change out your shocks is also a good opportunity to perform any upgrades, if you're interested. Performance shocks are appropriate for heavy-use daily drive vehicles, especially trucks.[3]

    • Coil shocks are manufactured with a coiled spring around the body of the shock, which supports the weight of the vehicle and controls the movement of the suspension. These are adjustable, which means you can alter the height of your truck for optimum performance.[4]
    • Twin-tube shocks have a set of tubes, one inner and one out, that house the piston, along with a layer of shock fluid and air, which can have a tendency to create a foamy, frothy mixture that can affect performance, though some modern variations feature a nitrogen mixture that addresses the issue. These are common on off-road vehicles.[5]
    • Monotube shocks feature a tube and two pistons, which work essentially like the twin-tube shocks work, with one piston separating the layer of nitrogen from the air. It runs cool and is a popular performance choice for trucks.[6]
    • Reservoir shocks are filled with fluid, and either pressurized air or nitrogen. As the shock absorbs bounce, the fluid contacts the gas, causing resistance and dampening the spring action.
  4. 4

    Jack your vehicle in an appropriate location. [7] Park your car on a level surface and loosen the lug nuts on both sides of the front or back end. Secure your vehicle with ramps and/or jack stands. Check your owner's manual for the correct jack positioning. When you've got the car up, remove the wheels and locate the shocks.

    • Shocks will be affixed with a vertical bolt that has to be extracted from within the engine bay or the trunk, or may be positioned at the top by a horizontal bolt that has to be unfastened and knocked out of position.
  5. 5

    Check the shock mountings and spray them with metal cleaner. The most difficult part of the job is removing the old shocks, which can have a tendency to be really gunky with both age and road-grit, making the bushings and bolts somewhat difficult to remove. Check out the mountings to see if they're loose enough to get off, or if you're likely to crack the rubber around the bushing. It's ok if you do, since you're changing out the shock anyway, but it's usually easier to spray some WD-40 or PB Blaster in there and let it sit for a few minutes to try to loosen things up before you get to work.[8]

  1. 1

    Remove bolts from the shock tower. Lots of cars have the top bolts under the fabric in the trunk of the car, which means you'll have to lift up the lining to get to the shock bolts and remove them with a ratchet and socket. As always, consult your shop manual for more specific guidelines regarding the location of the shock tower bolts. In general, though, they'll be in the trunk.

    • To unfasten the bolts, turn the socket and ratchet counterclockwise, greasing the bolts with penetrating fluid to eliminate any surface rust, if necessary.
  2. 2

    Disconnect the shock from the suspension. Use a socket set or a nut splitter to disengage the nut that connects the shock to the suspension, and remove it from the bolt. If there isn't enough room to operate the splitter, you can apply penetrating solvent.

    • Depending on the assembly, you may also need to disengage the knuckle at the top of brake assembly to get the the shock. Consult your owner's manual to find out for sure. Use the same process to remove the nut that is positioned at the top and keep the nuts separate so you will know which one goes where when it is time to install your new shocks.[9]
  3. 3

    Remove the shock absorber from the bottom and top bolts. Wiggling the shock off the bolts can be surprisingly difficult, especially if the shocks are mounted on studs with a retaining bracket and everything's rusty. Wiggle it around a while and it should come off eventually.[10]

    • One common frustration occurs when your piston rod keeps turning with you as you're trying to loosen the nut. You can use locking pliers on the end of the rod and keep it from turning with the pliers while loosening the nut with a wrench, but that can be just as frustrating. There's a hollow hex kit that fits over the rod and a tailored wrench made for the purpose, available at any auto parts store for about eleven bucks.
    • If you need to bang on the bolt with a hammer or the end of your wrench to get it loose, that's ok, but make sure you put one the nuts back on to use as a hitting surface. Don't risk misaligning the bolt and messing up your ability to reinstall the shock properly. Let the metal cleaner do its work and take your time. It'll give.
  1. 1

    Fit the new shock back onto the suspension control arm. You might need to use some pressure to constrict the shock as it falls into place, and you might need a help to help lift the suspension back up to reinstall the bolts in the correct positions. It can be kind of a balancing act, so it helps to have another set of hands. Screw on the nuts hand tight.

  2. 2

    If needed, you may once again affix the anti-roll bar if you removed it earlier. Reattach it and screw the bolts back on hand-tight. Replace the shock tower nuts you removed at the beginning of the process, probably in the trunk of the vehicle.

  3. 3

    Check your torque specs in the service manual. [11] Before you go tightening everything back down, recheck the specifications for torque to be sure everything's secure.

  4. 4

    Repeat the steps to replace the other 3 shock absorbers, if necessary. [12] Most of the shocks should wear out at the same time, so if you're going to do one, you're probably going to end up doing them all. Do in following the same steps and then put the wheels back on and tighten the lug nuts to finish the job.

Add New Question

  • Question

    How long does it take to change a shock absorber?

    Hovig Manouchekian

    Hovig Manouchekian is an Auto Repair and Design Specialist and the Manager of Funk Brothers Auto, a family-owned business operated since 1925. With over 30 years of experience in the automotive industry, Hovig specializes in the process of auto repair and maintenance. He is also very knowledgeable in common automotive issues and needs including engine repair, battery replacement, and windshield accessory and maintenance. Hovig's knowledge and hard work have contributed to Funk Brothers Auto winning Angie's List Super Service Award for five consecutive years.

    Hovig Manouchekian

    Auto Repair & Design Specialist

    Expert Answer

    Shocks are pretty straightforward—you usually just have to disconnect the top and lower mount to be able to remove them. However, on certain cars, you may need to remove some paneling to gain access to the shocks.

  • Question

    When replacing rear coil springs, should I apply any sort of grease?

    Community Answer

    It's not advised, as grease will attract dirt.

  • Question

    What could the loud squeaking noise coming from my truck when I turn left or right be?

    Community Answer

    It could possibly be the pads on your front brakes getting worn down. Take it in to have the brakes and rotors looked at.

  • Question

    How long does it take to replace rear shocks?

    Community Answer

    It will take about 30 minutes if you're learning as you go. If you know what you're doing, it will probably take about 20 minutes.

  • Question

    Is it possible to put shocks in upside down?

    Community Answer

    Yes, it is possible. Look for indicators such as the word "top." If installed upside down, the life of the shock will likely be greatly reduced, and it will not function properly.

  • Question

    Should the bolts and bushes be changed at the same time?

    Community Answer

    Yes. Since you are in there already, you should take the opportunity to do that, too.

  • Question

    What do I do if my shocks have no tension on them? Are they supposed to move in and out freely?

    Community Answer

    That means they need to be changed. If they pop back up into place when you push them down, that means they need to be replaced.

  • Question

    How do I take the springs off the struts when replacing my shocks?

    Community Answer

    Use a spring compressor tool. Check at your local auto parts store, they should have it.

  • Question

    Can replacing my shocks cause my handbrake to stop working?

    Community Answer

    No, the handbrake is operated by a cable or by an electric motor in newer cars.

  • Question

    I have a 2011 BMW convertible. Do I cut the fabric wheel well cover to get to the rear shock?

    Community Answer

    It should be removed by removing some screws or plastic clips. Search for some information in the manual or online to find out where they are located for your car.

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit


Video

  • Grease the upper shock threads with WD-40 when you are removing the old nut.

  • Shock absorbers should be replaced approximately every 75,000 miles (121,000 km).[13]

  • These directions for replacing shock absorbers are generic. Consult your owner's manual or your repair manual for instructions specific to your car's make and model.

Things You'll Need

  • Owner's manual
  • Repair manual
  • 4 new shock absorbers
  • Jack and stands
  • Lug nut wrench
  • Socket set
  • Socket ratchet
  • Nut splitter
  • Penetrating solvent

About This Article

Article Summary X

If your car suddenly feels less smooth or even, or potholes feel more noticeable, chances are your shocks have become worn out. Luckily, replacing your shocks is easy with a little bit of time and know-how. To replace your shocks, you'll need to first purchase a new pair, which can be identical to what you're currently using or a performance upgrade, if you're interested. When you're ready to get to work, you'll need a jack to remove the wheels, WD-40 to help loosen the mountings, and a socket and ratchet to remove the old shocks. Start by removing the bolts from the shock tower. Disconnect the shock from the suspension and remove the shock absorber from the bottom and top bolts. Once you remove your old shocks, fit the new shock back onto the suspension control arm. To learn how to check your torque specs, keep reading!

Did this summary help you?

Thanks to all authors for creating a page that has been read 357,898 times.

Did this article help you?

How To Install Shock Absorber

Source: https://www.wikihow.com/Replace-Shocks

Posted by: byerlyellonly.blogspot.com

0 Response to "How To Install Shock Absorber"

Post a Comment

Iklan Atas Artikel

Iklan Tengah Artikel 1

Iklan Tengah Artikel 2

Iklan Bawah Artikel